admin

Marzo 23, 2020

Worm travel gearbox with motor
worm motor
A robust worm-get gearbox powered by an MM28 electric motor. Ideal applications where an easy to fit, high torque output is required. Ideal for student based projects including robots and buggies.
The machine has been designed so that the output shaft can be ‘clicked’ in and out for modification. Electronic.g. cutting down to size. The engine is snap installed into its cradle to activate the apparatus and worm.
Details
1 – 6V DC
0.1A to 1A depending on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
Overall dimensions of box + engine: 35(W) x 40(H) x 60(L)mm
The primary feature of this high-efficiency gear box is a worm gear, which locks the output shaft whenever the motor is not turning. The high equipment ratios of 216:1 or 336:1 get this to gearbox appropriate for little strolling robots, lifting mechanisms, and other applications where large torque is desired.
The low-voltage motors in the worm gearbox run on 1.5-4.5 volts and draft to some amps, making them ideal applicants for the DRV8833 motor driver carrier. Engine overheating can be due to excessive stalling, also at very low voltages. We recommend that you utilize stall-detection sensors, or just view your robot, to ensure that it doesn’t stall for more than a few seconds at a time.
This gearbox includes a 4 mm diameter, round output shaft, which works with the wheels that are appropriate for Tamiya 4 mm, round shafts. Our 3 mm universal mounting hub also suits on small threaded end of the shaft, although it is not especially designed to work with this kind of shaft (the hub’s set screw could harm the thread on the shaft).
Ever-Power gear motors are economical, right-angle, worm-geared motors that install easily found in the tightest applications. Economical right angle worm geared motors established new standards for reliability, effectiveness and economic climate with unparalleled features including hollow shafts in the tiniest sizes. An inverter friendly design offers easy integration today and a truly future proof solution. The Ever-Power gear electric motor offers total flexibility in mounting options includes shaft, base, face, and flange solutions. The electric motor terminal box could be mounted in choice positions rotated in 90º steps around the electric motor frame providing for unparalleled integration options.
Ever-Power gear motors adhere to UNITED STATES and International requirements, including NEMA, IEC, CSA, and CE, the Ever-Power series permits worldwide acceptance, a genuine total alternative for our global clients.
Superior protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dirt tight and hose proof,and can be utilized outdoors or in wet and dusty environments without the use of additional enclosures. Complete rated output is available at the result shaft of the machine.
Product Features
Power rating up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Completely enclosed, sealed against dust and water spray
Lubrication change initial after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50/60Hz
Enclosure IP65 (Standard), IP66 (Optional)
Additional features:
Connecting with Connect connectors.
With built-in inverter up to 7,5kW.
Ever-Power-Mark
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to EN 60034
Corrosion category based on DIN ISO 12944-5
C1, C2, C3, C4, C5-I, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm equipment motors are the answer for applications requiring a good corner turn, optional dual result, or an inability for the electric motor to be back driven. The DC correct angle gear motors are made for continuous and intermittent duty operation. Our right angle gear reducers are designed with several mounting plate choices, making them well suited for a variety of DC motor based applications. We offer 12 ratios ranging from 5:1 to 100:1.
10309
FEATURES
1/43 to 3/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Regular brush life of 2000+ time (varies by application)
EP Products Worm Gear Motors are made to generate high torque in a small package size. Worm Gear Motors are excellent for applications that want a personal- locking or breaking feature since the output shaft can’t rotate when there’s no power applied. Additionally, Worm Gearheads can transfer motion in 90 degrees. With various decrease ratios, precision trim gears, voltages and sizes, EP Products has a DC Worm Equipment Motor solution for the application.
Features and Benefits
Very High Torque Capabilities
Self-Locking / Braking Features
Motion Transfer of 90 Degrees
Ability to Handle Large Gear Reduction Ratios
High Durability
Low Noise
Flexible Configuration
Applications
Protection Door Locks / Industrial Conveying Systems / Security Gates / Teeth Seats / Ambulance Cots & Stretchers Many of our DC Motors can be complimented with among our Worm Gearheads. EP Products will work with you to create and manufacture a Worm Gear Engine that will optimize the performance of your unique application.
Built to your unique requirements
Engine Type: Brushed / Brushless / Coreless
Voltage
Output Speed
Power
Current
Torque
Reduction Ratio
Shaft Material & Size
Gear Material
Shaft Configuration: (D Trim / Round / Splined / Other)
General Size Parameters (L, W, H)
Encoder Type: Optical / Hall Effect
Additional Assembly Requirements (lead wires, connectors, etc.)
INTRODUCTION
The turbo metal gear worm electric motor uses a metal gear box for strength and a high torque output. Due to the special mechanical structure of the worm drive the electric motor output shaft is usually self locking and can not be rotated.
This part runs on the two wire connection and supports direction control and also PWM speed control. Ranked voltage is 12v and can attain 40RPM, with a torque of 8kg/cm.
SPECIFICATION
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Ranked Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear units from EP DRIVESYSTEMS especially show their power in applications where great gear ratios are essential. Our worm geared motors are for that reason optimally suited for use in intralogistics, packaging technology and the meals & beverage industry.
Four great reasons for EP worm geared motors:
Rugged
Our worm geared motors have a high overload capacity
Maintenance Friendly
Washdown versions allow simple and efficient cleaning of the get system.
Corrosion protection
The NSD tupH sealed surface conversion is exceptionally chemical, corrosion and abrasion resistant.
Flexibility
Our modular design give users maximum freedom.
The modular system for maximum flexibility: Our EP worm gear units
There are numerous applications that want drive systems, and each of these has its unique requirements. The EP series worm gear motors could be quickly and efficiently adapted to meet your needs.
Worm gear models impress with their high power density and small design. If required, we are able to also source them with the highly effective nsd tupH surface treatment.
As well as the basic EP housing, we offer an extensive type of bolt-on elements to customize the product including torque arms, shaft covers and output flanges. These can be easily field set up, but we will also be happy to assemble the individual components for you.
Find out more about our modular SI worm geared motors!
Find out more
Smooth and Clean: The EP worm gear unit SMI
SMI worm gear units feature a soft, corrosion-resistant alluminum alloy housing. Optional nsd tupH surface conversion makes this product preferably suited for severe and challenging industries like food processing and pharmaceuticals.
Adaptable input designs such as for example NEMA, IEC or immediate motor mounts in additional foot or flange mounted housing designs.
Worm geared motors
Worm geared motors for small power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared electric motor program. The units have got on all sides different fixing possibilities and enable an easy assembling for the client.
Other drive configurationscan be designed by use of built-in accessories (e.g. torque arm and output flanges). The housings are created in light weight building out of aluminium die cast. Engine attachment is realised generally by way of IEC adapter B5 or B14A.
Technical Data
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:result shaft, output shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly/mounting:uniblock, flange, torque arm
Buy Worm Travel Gearbox with Motor – incorporating the following features: 1 to 6V voltage rating, 17100 rpm simply no load acceleration, 220g-cm stall torque, 3mm shaft size, 60mm long, 35mm extensive, 40mm high, a robust worm drive gearbox powered by an MM28 motor (included), most ideal for applications where a simple to match, high torque productivity is necessary, nylon housing and equipment, requires light oil or perhaps silicon grease lubrication, ideal for student based projects including robots and buggies.
Most ideal for applications where an easy to fit, high torque outcome is required
Ideal for student based projects including robots and buggies
Reversible Great torque Turbo Worm Gear Motor JGY370 DC 12V 40RPM
Reversible Excessive torque Turbo Worm Gear Engine JGY370 DC 12V 40RPM
Features:
The engine is Gear DC electric motor with micro-turbine worm, you can change the wiring-connection to improve motor rotation.
Turbo worm geared engine with self-lock, that’s, regarding motor without electric, the outcome axis is fixed, self-lock.
The reducer output shaft arranged vertically with the motor shaft, whole electric motor output shaft relatively-short than general gear motor, trusted to be installed the dimensions requirements strictly occasion.
Specifications:
Model: JGY370
Voltage: DC12V
No load speed: 40r/min
Result torque: 5.6kg.cm
Rated current: 0.06A
Weight: 163g
Application: open the windows, door, Mini winch. Ect.
In sumo robot or combat robot competition where huge holding torque’s motor is essential in order to avoid your robot being pushed by your opponent robot. The worm equipment is definitely a better option compared to the spur gear motor. How come worm gear so special? Check this wiki out: Worm Travel.
“Unlike with ordinary gear trains, the path of transmission (insight shaft vs result shaft) isn’t reversible when using large reduction ratios, due to the better friction involved between your worm and worm-wheel, when usually a single start (1 spiral) worm can be used. This can often be a advantage when it’s desired to eliminate any likelihood of the output driving the input.”
In other terms, it is hard to push your load (example, your robot) if the motor is not power or rotate.
Features and Spec:
Metal gear box
Result shaft is self-locking because of the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
Weight: 150g

We give worm motor; call us to locate out more.